Dual Sport, Offroad Bikes

The watercooled version, it doesnt matter if original or by someone else, even used. Ive seen that there are 110 versions by polini but i was wondering if the dt 125 cylinder and piston will fit?

i just bought an xt 125 x 57 plate for £800 but the clocks have broke the lad said he was trying to wire up and alarm but the clocks popped the "MPH" is aways displayed is this a common fault ?

Hi all, I,v just finished a rebuild on my 1977 DT 175. Its all going not too bad, but the speedos not working. I,v checked the cable and the drive all seems to be working the fault seem to be in the clock. When I turn it by hand it some times works. The thing is, can you take them to bits to check inside? Any advise would be good. Thanks Wullie

Hi , does anyone know if I could swap front end for a motocross front end with upside down forks and swap to excell rims and talon hubs. So can use brembo brakes etc. Is it do able and how hard would it be ?

Hi there, I have asked this sort of question before and am sorry, but i have a friend who has an Aprilia MX 125 supermotard the measurements of his front forks and rear swing arm are about equal to my DT125RE(from my measurements my DT may be a little wider) does this mean that those wheels and other wheels of this type could be spaced to fit? his rear wheel is wide and really tops off the 125 making it look like a bigger supermoto bike. any help will be appreciated thanks Jake EDIT: front: 3.00" x 17”; rear: 4.25" x 17” <-specs

i have a yamaha dtr 125 its been bored out but from normal its been bored out 2.5mm oversize what cc will it make the bike ? any one know

Yoo Does anyone know the best chain/sprocket for a dt125 2001 for acceleration? If so were could i get it from ? Thanks Everyone!!

This is probably a silly question but can anyone confirm that the TT600RE speedo should illuminate when the light are on.? If as I believe the answer is yes any advise on how to replace the bulbs as, as it's now dark I've just noticed mine is not visible at night.

hi im restoring a dt 50mx on a 1992 plate. i boght the bike mostly all there i have a bit of a problem though. the carb slide and neadle and sprig is missing if anyone knows where i can buy these parts. if i can't get these parts i will buy a full carb just wondered if anyone knows where i can get one. any help would be appriciated. thanks dan

Hi can anyone point me in the right direction regarding where to obtain or the compatibility for a locking fuel cap for a 2003 Yamaha TT600RE which has had a larger tank fitted, make Acerbis?

Does anyone know if a dep silencer fits into the big one(fresco) expansion chamber i have been told by a couple of mates it does but just want to be sure as i have the dep silencer and looking for a exhaust. and cant really afford the dep so going for the big one. thanks for any help

hey, i'm currently replacing the little end bearing on my yamaha dt50mx but i'm not too sure on how to out the new gudgeon pin clips back in?

i have a yamaha dt50mx 5 speed and when i'm comming to stop i'm going down the gears but ocasionally it will stick in neutral and i can't get down to first without going back up into second and knocking it down again. any ideas on the causes?

i sent an e-mail to my local yamaha dealer and they just havnt got back to me about new handle bars i was just wondering which ones would fit, or if i could straighten them again so whn i come to sell it it doesnt look bad :/

heya everyone i bought a 2007 dt125x supermoto a couple of months ago, i have taken the snorkle of the air box, bought a dep end can but now i need the front half of the pipe. my standard one is pretty wrotten so no point in gutting it out. does anyone have a dep front pipe for sale to fit my 2007 sm?? and also a cdi to fit my bike. basicly i want it as fast as possable and to sound as nice would be very greatful for any help and especially greatful if someone has an exhaust for sale. thanks Harley

Hi I'm new to this forum and own a 59 plate xt660X that I use for knocking around the back roads on. I am trying to get hold of a mudguard extender for the front mudguard but cannot seen to find anyone that makes one for this bike. Would be really grateful if someone could point me in the right direction here. Either to a supplier or if anyone knows if the same guard was used on another model. The MT-03 looks as though it might be close. Thanks in advance.

Just wondering what an engine rebuild consists of and how do you know when to do one? Thanks!

hi ive searhed internet to find some new plastics for my dtr 125 i think its 2002, not sure as th bike is stolen/recovered. carnt seem to find new plastics anywhere. has anyone got any ideas. could i put plastics on that r not 2002 modile? cheers chris

hi just wondered what 2 stroke oil best fot dtr 125 cheers chris