The Bar

Can anybody help me to find out what type of Yamaha this is... I think this is around 1980-1982 of Yamaha.. This is 50 cc i know this is very bad pics but this is the only pics i found And if sombody know where i can get some parts for this bike please let me know Thanks Toni

Hi can anyone please tell me how to countersteer as I have read alot about it but don't know how to do it. Many Thanks Gra Chesterfield

Hi all, Does anyone have a recommendation/comments when it comes to getting those extra or ultra bright light bulbs? I am looking at replacing the R1 bulbs with some Piaa bulbs, I know they are not cheap but if I get twice the dazzle it might make people see me , I have not seen any other bulbs that offer twice the light output for the same current. Thanks

Got a good start this morning…..was throwing a leg over the Beast right @ 4:20am. Nice & clear weatherwise…..ended up making good time as traffic was just shy of Non-existant. Here’s a nice view of Mt. Hood from the East side just @ the edge of the Warm Springs Indian Rez….. Musta got my wires crossed with my friend…..as he wasn’t home when I got there. I figured he was either @ work or up Skiing (lucky Bastid) , as the weather woulda been perfect for a day of Spring Skiing. So, I had to check out the view from the top of 4,000ft. Pilot Butte while I was here…… I then decided to set off for the Tumalo Reservoir area myself….. & Wha…

http://www.livevideo.com/media/playvideo_f...0EDCE43E260BFCC

Hi All Well now i have done it, after riding for years "when i was a lad" (but never passing my bike test (i know im a kn*) and being turned to the dark side by them 4 wheeled things, i have now bought a XV125 Virago. Been thinking about bikes for ages now but always resisted as i know i will be hooked on them again (I had an 80cc sports bike and did 23000 miles in under a year, mad or what) What finally did it was sitting in the queues at the blackwall tunnel for the past 6 weeks and watching with envy as the bikes slip past (well they do by me coz i get out the way) it was getting to be 3 hours to get to work and 2 to get home (only 40 miles) Pick it up…

hi everyone new to the forum just got a r6 and i love it

im still fucking here

Does anyone know if there's an easy way to replace the bulbs behind the speedo on a thundercat without having to remove the whole bloody fairing?? - according to haynes the fairing has to come off, seems a long old job just for a bulb!!

hiii

captions please

I am new to the site and im already feeling welcome and I couldnt be happier to own a yamaha!!!!

Hi all, new to this site. I need advice on how to attach files in a reply. Have some thundercat manuals in pdf format to stick on for someone. Many thanks for any help

Question concerning the fazer headlight. I'm fitting a fazer headlight to my fz which I might say is taking some time due to the amount of fibre glassing. I would like to now if the lefthand light when you're on the bike is wired to the dip or main beam. If anyone can let me know I would appreciate it. Thanks

Hi everyone any help would be very much appreciated, I bought a Aolin 2 way pager alarm from ebay! and theveryone wanted atleast $200 bucks to install it which i didnt have,so itried to do it myself, i got the alarm working fine with arming and disarming, but i cant seem to get the remote start to work, the manual says that every bikes up and down engine stop wires are black and white but i cant find any black and white wires, but i did find a red and white wire that when i tested it with the engine on and off switch the tester lit up. the diagram also shows 4 wires for the ignition and my bike only has three coming out of the ignition, can someone please help?????? Thank…

Hi, Could someone tell me if the front end for a fzr 750 genesis (1988) front end is the same as the front end from a fzr 1000 genesis (1988) front end Thanks, Nick.

hello everyone new here and need a favour already can anyone tell me wether an electronic speedo drive will fit and work in my xv 1100 front end if not what is the drive ratio on the mechanical drive the weathers here and I need to finnish me bike and get out there.Thanx

Hi everybody, I'm a newby to the forum having just upgraded from my NC35 to a 2003 R6, which I'm absolutely loving, as the following story will prove.... So I've had the R6 for a grand total of 9 days now, and coming home from work last night I was getting bored of dumb ass drivers sitting in the outside lane of the 3 lane section of the A40 and leaving the two other lanes completely free, so I took the decision to undertake the lot of them in the inside lane at a speed approaching 3 figures in a 50mph area. Unfortunately one of these cars turned out to be an unmarked pig in a BMW 5 series. He eventually caught up with me in traffic and pulled me over for what I was t…

I have an '85 yfm 80. somethings wrong with the steering somewhere and it wont turn sharp at all. i mean, i have a bayou that turns sharper than this thing. i know that it should make tighter turns than it does because ive ridden one very similar to it (same make and model) and it was the tightest turning quad iv ever ridden. if anyone has any suggestions please let me know.

I bought my 94 SecaII last October from a motorcycle enthusiast. This guy had bought it from a husband and wife and the wife rode the SecaII and her husband had another bike so I'm pretty sure that my bike was not abused (as it was ridden by an older woman). The guy I bought it from did some work to it such as: jet kit and carb rebuild (dunno what stage jet kit), K&N Velocity Stack intakes for each carb, he replaced the vacuum fuel pump with an electronic one that would normally go on an ultra-light aircraft - he said he matched the PSI of the electronic pump exactly (somewhere around 4 PSI) and also installed a Vance&Heines 4into1 exhaust. He only put about 500 m…