The Bar

I followed a TMax home today armed with a fantastic loud exhaust... I was unable to catch him and ask for details for where he got it... Any ideas where I might be able to purchase such a pipe..?

82 xs 400r i was looking for ***** for my bike any one have any cheap but good carbs in mind.

as the title says , MERRY CHRISTMAS LADS N LASSES,hope your day is eventfull.

Got another xmas pressie today; got into the top 10 in bike exif for 2011! 5. Drew's Yamaha XS400. It’s usually Yamaha’s XS650 that gets the custom treatment. But this sharp tracker from England, with an XS400 motor in an XS250 frame, proved that size isn’t everything. http://www.bikeexif.com/top-ten-motorcycles?utm_source=feedburner&utm_medium=email&utm_campaign=Feed%3A+Bikeexif+%28Bike+EXIF%29

Merry Xmas everyone, all have a good one and have lots of fun on your bikes next year whether they be yams or not. Special thanks to alexasigno for providing the forum which breaks down at the most inopportune times and all the regulars that just 'make it happen' Looking forward to a few days out with you again next year ...Paul

more here

Hi Guys, Just wanted to say Hi! Im new on here and am getting a Yam DT125R (MK I) next week. Hopefully i'll be able to help others, but my knowledge is limited so for a while i'll be leaching for a while . However I do know IT very well so can scratch your back etc... I Live in the UK (Hampshire). ta St0F

Any info on reducing the lean running of this bike, low revs almost means stalling. Changed the pipe and no difference, into the electronics we go! Info?

Have you given your yam a name? if so why? I call mine Marmite, it was suggested on this site I called it Winker, but that might have been a spelling mistake, LOL, So come on and lets us know.

anyone know the torque value to tighten cylinder studs and nuts to?

Hi There everyone. As the bad weather stars to come in a problem i have allways had with my visor is it steaming up and wala in seconds i cant see a thing. Now i know about Pinlock inside visors but i just cant afford one. There is riding with it slightly open but then the wind hits my eyes to hard and i have to keep blinking and you loose the water seal at the top of the visor and as most helmets go the ventelation system is... well crap. I currently have a basic Nitro skid lid and ive never owned an expencive one so i dont know if mor expensive visors work better but i cant afford one. Is there any other way to make it so it doesnt steam up as i go along or will i…

Hi there, just wandered if anyone can help me? I have a 1988 DT125r that has been sat in my garage for 3 years and not run? Now i need to get it going and guess what, it won't go!! I took out the carb and cleaned that thoroughly aswell as cleaning the jets and the float bowl. I then cleaned the air filter out and put carb back in situe. I replaced the throttle cable as it was knackered. I put new gear oil in as a precaution then cleaned the fuel tank out and replaced it with clean petrol and oil. I then cleaned the fuel filter and replaced the entire fuel line aswell. I put a brand knew start button on it but for some reason it wont go!? There is a spark when i ki…

is it posible to fit a dt400 engine on a dt175 frame if so how much work needs to be done?

Is it possibly to fit an oiler cooler to my t80, seen them on cubs and fancy one, what would involve in fitting them. http://www.pitbikeparts.co.uk/cooler-used-engines-p-723.html

Hi, i went out to the garage the other day to finish up my project bike, bleed the brakes and what not, which is when i found that my rear Calliper was completely seized on the FZR. I either need to know what Calliper will fit on it (its an L reg bike) Or need to know if anyone is selling a like for like replacement? I'd like to be able to put an R6 brake on it, but don't know whether it will fit.. It has a lot more power than it would of as standard so yeah want to update it but not worried if i can't. Cheeeeers Best off to email me on [email protected]

Hi everyone. its been a hard day, i now have a new hobby where i buy and sell generators and petrol powered equipment, basically i bought some generators ars spares or repair, most of them run but there are two that as of so far have beat me... 1:) SIP Medusa 950 generator, two stroke, spins over, has spark, has fuel, will not start 2:) SIP Medusa 950 generator, two stroke, spins over, sparks, used to run if petrol was put down the spark plug hole but now it doesnt start at all even if span over with a drill,. im at my wits end with these two, the other units i bought used to come to life after a few pulls and a bit of persuasion with some petrol down the plug '…

want to fit a tail tidy to my bike any tips on which is the best to fit still going to use the standard indictors that came on the bike unless any one has any better ideas. thanks for any tips

Just purchased a 05 R1, had it out for a couple of runs, no problems, tried starting it yesterday after been stood for 2 weeks and it would'nt start, turned over & over til battery died, recharged battery tried again same problem, HELP

Hi All, Just going to ask if anyone has used Philpots at PITTED FORKS in Luton to have any of their rechroming done, just bought a spare set of forks off of ebay to replace my old knackered set and Philpots want £156 all in inc P+P for a full hard rechrome of the stancions fully guaranteed for 12 months, sounds like a good deal to me but do you know better? If you happen to know of a better deal please give me a call or PM me if you want to check them out for yourself then they are at www.pittedforks.co.uk. Martin. P.S It seems that due to demand there is a 4 week turn round on their jobs but as the bike is laid up for the winter not a problem for me but might be for s…

Hi everyone. When I first start the bike in neutral and put it into gear the bike stalls( clutch is in and so is the kick stand). I first thought it was the kick stand switch not working properly--I had that cleaned off and looked at seemed fine. Still I experience this problem and I am not sure what it is. I'm not sure if it's a clutch issue or something else. When its warmed up after riding I can put it into gear just fine. Another issue I've noticed is when I'm downshifting the bike will have a hard time going into first, it sometimes will get stuck in neutral and I'll have a hard time getting it back into first. Has anyone experienced something like this befo…