Everything posted by blackhat250
-
Northern Rockers Rumble
Am at Blackpool Triples Rally that weekend,,, hope to see some britts riding down from here, I take the A7 -A6 ..friday .
-
Now THIS is an adventure...!
Great story, the video Terra-Circa is brill too . Austin Vince. awesome trip on DR350"s . long before Boorman & Co.
-
Recently started motovlogging.
Is my volume fked " or is it quiet... Avitar looks like Guy Fawks
-
Hi guys need some help please :)
I think you"ve confused the Tailpipe with manifold, unless you"ve a numberplate on front mudgaurd,
-
xvs950a accesories
Shall we see them in your next video. And the bars
-
Got the second RD400
Thats what happens when you have too many bikes, . am offloading the DT125, . got rid of the illiminator in october ,
-
YBR 125 Wont start
" all the adjusting to compensate lack of idle, And check your throttle cable . if this is tight , no amount of screw adjustment will help. . back off cable to drop slide . back off idle screw , and start again to find idle,,
-
xvs950a accesories
Is that skelton hands .or oyster shells...
-
Hi guys need some help please :)
Yeh" spray behind the flywheel with an excelarent . [ WD/ Brake cleaner/ carb cleaner/ ] while bikes running " if the seal is worn / hard. it will pull excelarent into crankcase, and revs will increase , was the bike unused for a spell , ? The other seal R/H. pulls gear oil thru [ when worn] and smokes heavily,
-
Mini Project XS 400 DOHC
They remind me of a Honda [ style] 250 in the late 70"s , think it was a single with twin exhaust head.. RS250 maybe,,
-
Hi guys need some help please :)
Were on the same track DT50 "
-
Hi guys need some help please :)
Was the idle fine when engine cold, ? how old is this DT
-
Hi guys need some help please :)
I take it that was the idle screw , you backed off" large knurled edge, not the air screw[ small cross head ] ? As the idle screw just raises and drops the slide. a small amount should not cause engine to die,
-
Mini Project XS 400 DOHC
Ah" i thot this was the project bike,,,i did think it was mint.....
-
Spirit crushed: took the car
Bippo" you are Hardcore,
-
YBR 125 Wont start
It will be crude, i am 100% shure this is the problem" A drill my be too big. thin wire. ultra sonic would shift it, poke in from the low hole too. this needs to be clear , as fuel passes thu low hole, fills to float level. choke pipe feeds off here, ,,, While blasting [carb or brake cleaner] spray up feed pipe too, while choke lever in open position
-
Mini Project XS 400 DOHC
Thats tidy" did you get her running, them CDI"s are better remade by Speedshop or west county windings,
-
YBR 125 Wont start
Yip" this feeds the choke jet. not the brass pipe in centre, the hole on bowl edge, a pipe [on carb body] drops in there, blast it clean thru, And picture of choke lever is correct for off , when lever lifts it opens choke jet. by means of plunger it connected to.
-
NEWBEE
Hi panicbar" first time av seen a neebee post hi-jacked,,,,like your style...
-
Got the second RD400
Yeh" Kev"s a bottomfeeder Land scaper. i mean, Foamy" you"l find the pub going females are all nutters, just watch that vally"s or geordie shore, And i married one , and most after that were the same, am afraid its the type you attract mate...
-
Gilera 4V project
Look same as Garelli tiger filtre. "
-
Hi guys need some help please :)
Am thinking dirt in fuel tank, as it ran well for short time, now carb could be choked again . run fuel into CLEAN container
-
Hi guys need some help please :)
Yeh" but the coil may breakdown once hot, lets try the simples first tho..
-
Hi guys need some help please :)
Pull the fuel pipe [ tank] run it into a jug. see if flow is interupted.
-
Hi guys need some help please :)
Well done hichy" its a learning curve, hope she rides well now,,