Naked

the battery is new and dead again...is it the magneto or the regulator or the battery again...already change the regulator for a second...what test can i do..thanks

ok so im planning on going for my full bike licence and the bike im after is late 80's early 90's fzr600 (with the twin round headlights). Reason being is i like the older styling, what do they handle like? Are they a good bike? Reliable? My first thought was an r6 but they are to new for my likeing and at around £2k, alot of money to stack. Any information on the fzr would be grea thanks

Hey all. I just bought a 1995 FZR600 and I've noticed that the clutch tends to slip when you get on the throttle harder in 3,4,5 gear. If you're accelerating normally and fast it's fine but when you throw it down it slips. I just got the oil changed today (Yamalube 20w-50) and it's still slipping. The clutch cable is set up to engage pretty late so I'm going to adjust the cable to engage midway and give it some slack. The bike needs a new fork seal and with this clutch thing, I'm assuming wheelies were done with this bike. It might just be the weather too. When I test drove it, it was in the 60's but I'm not sure how hard I pushed the bike. Today I rode it all over …

Hey folks. New to the forum and looks like lots of good info that I will need. I've been trying to id the engine in my bike. Number is 3hh-108856. I was told it was a 2000 but I doubt that. I'm thiking more like a 1998. Any help is greatly appriciated.

Hi, I'm new to Yamahas and have recently bought a 1996 FZR600R, the old foxeye model. I want to change the fork oil, can anybody tell me the correct amount and grade of oil per leg? Thanks very much.

can anyone tell me if the fzr400 lower panels fit the 600 just cant find 600 panels ? cheers all

i pulled my 98 FZR600 out today after sitting in the garage for the winter and after i finally got it started i noticed it was missing on one cylinder. i checked all the sparkplug wires for spark and they were fine. i put some new gas in with seafoam and ran the bike at high rpm for a while and still number 3 cylinder isn't firing. i figured out it was number 3 by taking the airbox off and spraying some starting fluid at each carb while it was running. i sprayed each carb individually and the idle wasn't affected when i sprayed number 3. my question is, what should i try next? i figured i'd get some new spark plugs since it's cheap. but if that doesn't work wha…

Help !!!! I need a favor. I think my frame is bent. I need the distance from the top front of the neck to the large main cross brace above the swing arm bolt. (appx. 1.25 diameter tube). Should be around 27 13/16 (27.8125) inches or 706.4375 mm. Went to test fit the tank cover and does not fit with the upper fairing bracket on. Top of frame appears to be short above the engine. Installed engine cradle and they are low and forward of the rear bolt holes.

Hi all! Got a query regarding my fizzer! I got an fzr600r on a 95 plate (incase you didn't guess!). Does anyone have problems with excessive softness in front forks? And gotta say I had the bike 6 months and think its an excellent all rounder!!! Dean

Yamaha FZR600R '95 - here's a video

I have recently purchased a FZR600R and am wanting to improve its bottom end by getting a chain and sprocket kit that runs 45/14 rather than the stndard 45/15. Does anyone know who makes them and where I can get one from? Thanks

Hi ive got a 1995 fzr600r and im in need of a pair of front discs. Does anyone know where i can get them? The cheaper the better! Cheers

i have purchased an fzr600r (95) can anyone tell me if there is anywhere i can get a manual for it or if they even published one

Single seat cover http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=300518503256&ssPageName=STRK:MESELX:IT shock and swingarm http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=300518509927&ssPageName=STRK:MESELX:IT

mate has just bought a fzr600r race bike with a rod poking through the crank case .... not very nice, when we are replacing the engine can a thundercat engine be bolted straight in (physically they are identical) but it's the wiring loom and carbs exhaust etc..... i dont see there being much of a problem but any helpl would be appreciated. p.s. the broke engine has a tuned head, although i haven't lifted the head yet to see where the piston is burried thanks Crow

I have these going spare, if anyone wants to make me an offer for them, feel free otherwise I'll e-bay them

I've just bought a FZR600R '94 which when I start riding after the weather has warmed up will need a new set of tyres. Can anyone recommend a good pair of tyres to fit this bike??

hi there I have bought a new FZR600 rear shock which I was going to fit to my FZR759R until I found out that it was just to long to fit I had hope to raise the rear of the bike using the longer shock can anyone tell me if this modification can be carried out by fitting the 600 dogleg bottom suspension arm many thanks

hi there I have bought a new FZR600 rear shock which I was going to fit to my FZR759R until I found out that it was just to long to fit I had hope to raise the rear of the bike using the longer shock can anyone tell me if this modification can be carried out by fitting the 600 dogleg bottom suspension arm many thanks

I have just bought a 2004 Fazer 1000 and I need to fit new tyres, what is the best tyre for the bike, I'm used to Bridgestones. Cheers