feliks Posted April 4, 2014 Share Posted April 4, 2014 I used to do paintless dent removal for a little while with my brother-in-law, did lots of hail dent fixing.... gas tanks are a bitch to fix but they can be done with glue tabs and a puller. Put a glue a tab on with hot glue, use the puller until the tab comes off...repeat until dent is gone. Link to comment Share on other sites More sharing options...
Moderator Cynic Posted April 4, 2014 Moderator Share Posted April 4, 2014 They dont give up do they. The tank has been done with por15. Pull the dent, destroy the coating. Looking good though, Link to comment Share on other sites More sharing options...
rzresurection Posted April 4, 2014 Author Share Posted April 4, 2014 They dont give up do they. The tank has been done with por15. Pull the dent, destroy the coating. Looking good though, They all have good intentions and are willing to help. I appreciate that. Like you said - don't mess with the coating. Thanks for the compliment Cynic. Link to comment Share on other sites More sharing options...
rzresurection Posted April 4, 2014 Author Share Posted April 4, 2014 Onto to this next Link to comment Share on other sites More sharing options...
rzresurection Posted April 7, 2014 Author Share Posted April 7, 2014 Bought a couple of these off eBay today. I will use them to switch my rear signals. Link to comment Share on other sites More sharing options...
rzresurection Posted April 7, 2014 Author Share Posted April 7, 2014 I think I'm going to do the vintage Yamaha speed blocks in white (on a black bike). I like the two tone. Link to comment Share on other sites More sharing options...
feliks Posted April 10, 2014 Share Posted April 10, 2014 They dont give up do they. The tank has been done with por15. Pull the dent, destroy the coating. Looking good though, Was merely stating another method for removing a gas tank dent, in case anyone else was curious that came across this thread. Stripes are gonna look sweet, just need to move them down a tad so they won't get cut off at the seat! Link to comment Share on other sites More sharing options...
rzresurection Posted April 18, 2014 Author Share Posted April 18, 2014 Got the tank prepped and shot some black. The black looks a little hazy. I shook the shite outta the can. I even put the can in hot water for a bit. Link to comment Share on other sites More sharing options...
dt502001 Posted April 18, 2014 Share Posted April 18, 2014 It was a little cold and to humid today for garage painting,let it set up for 24hrs and tomorrow or sunday when we are suposed to get into the high teens,,when the temp goes up the paint will flow better. Also make sure the parts are at the right temp/same temp or you will see the difference in each part.Always best to paint all the parts at the same time If your rattle can painting then make sure you get more than enough paint at the same time from the same store as different batches of paint dont blend well,Black not normaly so much of a problem but I have seen different shades of black from the same company. I have to get a new sticker for the bike forgot to do it and yesterday was my birthday,but the local office is open tomorrow till noon so might make a run up on sunday Link to comment Share on other sites More sharing options...
rzresurection Posted April 21, 2014 Author Share Posted April 21, 2014 It was a little cold and to humid today for garage painting,let it set up for 24hrs and tomorrow or sunday when we are suposed to get into the high teens,,when the temp goes up the paint will flow better. Also make sure the parts are at the right temp/same temp or you will see the difference in each part.Always best to paint all the parts at the same time If your rattle can painting then make sure you get more than enough paint at the same time from the same store as different batches of paint dont blend well,Black not normaly so much of a problem but I have seen different shades of black from the same company. I have to get a new sticker for the bike forgot to do it and yesterday was my birthday,but the local office is open tomorrow till noon so might make a run up on sunday I think the conditions for painting were considerably less than optimal. I knocked all the gloss down and now have some more paint. Today is supposed to be in the 20's, so it should be ok for painting. You are right about the paint batches. Same goes for buying carpet or anything that is made in batches. There are always batch variations. Sometimes they are quite noticeable. Happy belated BDay! Link to comment Share on other sites More sharing options...
jimmy Posted April 22, 2014 Share Posted April 22, 2014 You are right about the paint batches. Same goes for buying carpet or anything that is made in batches. There are always batch variations. Sometimes they are quite noticeable. Where are the carpets going on your bike Link to comment Share on other sites More sharing options...
wild foamy Posted April 24, 2014 Share Posted April 24, 2014 On the footboards if its a moto guzzi! Link to comment Share on other sites More sharing options...
feliks Posted April 25, 2014 Share Posted April 25, 2014 Where are the carpets going on your bike lol! Link to comment Share on other sites More sharing options...
rzresurection Posted April 25, 2014 Author Share Posted April 25, 2014 Shag covered seat. For you Brit boys, over here shag has a different meaning. Lol Link to comment Share on other sites More sharing options...
dt502001 Posted April 25, 2014 Share Posted April 25, 2014 LOL get the deep shag carpet and then do the old lady on it,,,, then it will have double meaning HAHAHAHA Link to comment Share on other sites More sharing options...
rzresurection Posted April 26, 2014 Author Share Posted April 26, 2014 Deep shagging on the carpet. Lol Link to comment Share on other sites More sharing options...
wild foamy Posted April 26, 2014 Share Posted April 26, 2014 Some of us just deeply shag the carpet its a lonely life... Link to comment Share on other sites More sharing options...
Moderator Cynic Posted April 26, 2014 Moderator Share Posted April 26, 2014 LOL get the deep shag carpet and then do the old lady on it,,,, then it will have double meaning HAHAHAHAEwww, round my part of the world 'The old lady and the old man' are your mum and dad.... Link to comment Share on other sites More sharing options...
AndrewElvisFan Posted April 27, 2014 Share Posted April 27, 2014 That calls for a Giggety Giggety! Link to comment Share on other sites More sharing options...
rzresurection Posted April 30, 2014 Author Share Posted April 30, 2014 I've had a chance to re-paint the tank and fenders now. 10000x better. I've knocked down the gloss on the black paint - I used gloss black and have done 2 part clear gloss that I will finish with. I've added another layer of glass to my fairing and now trimmed out. Just need to sand the surface of the fairing, do some minor patching, sand more, prime and paint. These arrived today. They will be used to switch power to my rear indicators. Link to comment Share on other sites More sharing options...
Recommended Posts