September 14, 201014 yr Author should i get a multi meeter and test it? and it seams to have plenty of power atm so dn what to do, btw how do pin it open? and will it make a diffrence?
September 14, 201014 yr should i get a multi meeter and test it? and it seams to have plenty of power atm so dn what to do, btw how do pin it open? and will it make a diffrence? Multi meter is one way to test it, a 9 volt battery 2 wires and a small light bulb works if you don't have a meter. Pinning the PV open will cause you to lose all bottom and mid range power, in exchange for a huge kick up the ass when you hit 6-7000rpm. Not a great idea for the road because it will need to be ridden like a hooligan. btw where abouts are you from?
September 14, 201014 yr Author Barnsley neer sheffield. and i do ride like a hooligan and would it be like rideing a yz 125? usta have one of those and it wasent bad on the road and how do u test with the light bulb?
September 14, 201014 yr Barnsley neer sheffield. and i do ride like a hooligan and would it be like rideing a yz 125? usta have one of those and it wasent bad on the road and how do u test with the light bulb? Not like a YZ, they have a wider power-band and some bottom end to keep you moving. Get a working bulb from a torch or similar. Fix the wires to the terminals and battery as shown. Wire as below, if the bulb lights you have a circuit.
September 14, 201014 yr Author ok thanks, will try that tmorrow , btw the bike dose about 70+ is that right or dose it sound restricted?
September 14, 201014 yr ok thanks, will try that tmorrow , btw the bike dose about 70+ is that right or dose it sound restricted? Doesn't sound restricted to me, restricted is around 55mph. Are you sure your PV isn't working right
September 14, 201014 yr Author i can take a vid if you like but it just gos clockwise. when i got the bike the wire was in the block and hasent made no diffrence to speed earthing it but i have a recept saying its derestricted. anychance a dealer could have "remaped" the cdi?
September 14, 201014 yr i can take a vid if you like but it just gos clockwise. when i got the bike the wire was in the block and hasent made no diffrence to speed earthing it but i have a recept saying its derestricted. anychance a dealer could have "remaped" the cdi? Not a chance, if they could remap DTR cdi's he would have a queue for miles of people wanting it done. Vids are always good
September 14, 201014 yr Author ok then, will take a vid tmorrow of the powervalve moveing any ogther pics i should take?
September 14, 201014 yr ok then, will take a vid tmorrow of the powervalve moveing any ogther pics i should take? Yeah a pic of Olga Kurylenko naked would be nice
September 14, 201014 yr who ??? haha going You asked if there were any other pics needed. Olga Kurylenko
September 15, 201014 yr Author not had time to take a vid but im happy with the speed atm so il just take it to an expert/ mate when i get fed up
September 16, 201014 yr You didnt need to cut the black one! Only the black with green stripe cable is required for earthing the cdi. All i did was add a piece of cable to the other side of the original connector block by crimping a bullet head crimp on so i could remove if i wanted and earthed it to the top yoke. Im not sure why you have cut the black one aswell as its totally irrelevant
September 16, 201014 yr Author You didnt need to cut the black one! Only the black with green stripe cable is required for earthing the cdi. All i did was add a piece of cable to the other side of the original connector block by crimping a bullet head crimp on so i could remove if i wanted and earthed it to the top yoke. Im not sure why you have cut the black one aswell as its totally irrelevant to put the green and black wire to the black wire
September 16, 201014 yr But theres no need to make it more of a job than it is, i found it alot easier and tidier to just earth the black/green cable to the bottom yolk but thats just me ...
September 16, 201014 yr But theres no need to make it more of a job than it is, i found it alot easier and tidier to just earth the black/green cable to the bottom yolk but thats just me ... Easiest way to earth the PV Ryan. You didnt need to cut the black one! Only the black with green stripe cable is required for earthing the cdi. All i did was add a piece of cable to the other side of the original connector block by crimping a bullet head crimp on so i could remove if i wanted and earthed it to the top yoke. Im not sure why you have cut the black one aswell as its totally irrelevant The black wire is the earth wire, so isn't irrelevant. ( see above)
September 17, 201014 yr okay i get you now, i didnt understand the other pics, But My ways still easier to explain
_33963e.png)
_83bc35.png)
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.