Dual Sport, Offroad Bikes

Got a yammah dt 125 that im rebuilding bought it as a spares and repairs job... is a runner was jsut pissing out fuel but i've had the Carb redone and just wanted to know if I'd have to re-jet it again considering I've got a DEP downpipe and A bigfoot box on it? Thanks

hay hay as the summers coming i want to go supermoto has any one tryed changing a standard Dtr to super moto? can i get away with just changing the front wheal or will i have to change both? any help on this matter would be much appreciated :)Stockers

am happy the way my bike screamzzzzz ryt now..........with this kind club, lotz of people would be amaze.....thankzzzzzzzzzz .......

any one have a dt175e 1978 enduro do you know where to mount the voltage regulator the rectifier goes under the gas tank but i have not figured out where to mount the voltage regulator so can anyone help me out? the yellow wire is the regulator connector i just cant locate where to attach the reculator

Anybody got any thoughts on wheel replacements for the TDR, bike is a keeper but as a maried slave to the system with 2.4 sprogs, morgage etc etc etc lashing out hundreds of pennies for some fancy stuff is a a stretch. Anybody got some realistic soloutions, am i right in thinking that one busted spoke may well be the beginning of the end for the rest of em? Cheers all. Edit:- been looking at central wheel. Rebuild my wheels with stainless spokes for about 80 quid a wheel? Opinions...?

Got to service a set of these forks, i know its 10w oil but does anyone know the correct amount of oil, its an 96 dt125 re model. Thanks Daz

hi every 1 ive just had me engine rebuilt and i started it everything was fine then i went to put in into gear and it stalled , so i striped it all down and checked it had all plates and push rod bearing and all is there ,i disconnected my clutch cable and put my bike into gear and pushed it but the bike isnt trying to bump start like it should the clutch is stil spinning it like am pulling in the clutch lever any idears ...regaurds ryan

hi my water pump oil seal was leaking and whilst riding there was some clutch slip but the oil was like milk i have changed the seal and i fired some 5w30 semi car oil in and it slips like fook now. but ive heard car oil is ok but im guessing not what would be the best oil to use and do we think my clutch is nackered now? cheers bry

I am looking for an electronic ignition conversion for a 1974 DT350A. Does anyone Know if someone makes one? Also if the front fender painted silver by the factory or if the fender is molded from silver plastic? Thank you Waddy

Hey guys, just bought myself a 1989 DT125 and am searching for info on the bike, what can/cant be done to it, what fluids to use etc. Anyone know what the suffix for this bike would be, ie: LC, R etc cheers in advance for help

I have an ole xt350. The spokes are rusting. I have cleaned and waxed the spokes but the rust comes back pretty quickly. I was wondering if anyone has painted the spokes. If so what did you use? Did you brush or spray it on? Thanks for the help Gary

Hello all, I am lookin for a way to install some turn signals and a brake light on my TT 600 1985 , Is there any aftermarket option availeble ??

So I'm trying to find a company that makes decent graphics kits and will make them to fit a specific bike. I've found quite a few but not sure about most of the ones ive seen. Has anyone bought any before and would they recommend any sites?

Rebuilding the engine on my dt, delved into my big box of spares and the barrel I had had different sized reeds in it to the one on the bike. And the inlet rubbers are only compatible with the larger reeds as they have a section of rubber that pretrudes into the reed block. The block is taller, wider, and deeper. The opening. Between the carb and reeds is also a different size, hence why the rubbers are not compatible. Which is standard? Could it be from a different year or a 125? And if the ones im using are not standard, in guessing ill need a bigger jet?

Hi everyone, I use mineral oil in my dt125 , i am hearing mixed reports on this over a synthetic, what is everyones opinion of it and how strongly ? Also i am looking to do some touch ups on the silver swing arm and black frame but for the life of me i cant find any paint codes or places that sell it. Preferably id like paint on paint , rather than spray cause its just touching up. Anyone know where or how i can get these?

is there a way in va to title a 175mx and make it a enduro with tags

I am unable to find my ID tool, I once had saved ...I think it's 90's model thanx

Thinking of getting a 250R, does anyone have one and can tell me what they are like to ride, especially on trails/ green lanes? Ive seen parts are pritty easy to get hold of and i know it will be reliable. Cheers

just wondering if anyone knows were i can get the metal cap that goes on top of the carburettor that keeps all the slide assembly contained. cheers

hello my DT125R has a few problems 1. won't idle with choke off, and sometime seems to stutter a small amount while accelerating from standstill but is fine once its at higher revs.. 2. it has a slight rattling noise coming from the engine, but it is neither small end bearing or big end bearing from what i could tell, when i checked them. and it has had this rattling noise for about 5 months now and if it was a bearing surely it would of been nackered by now. any help is appreciated thank you.