Dual Sport, Offroad Bikes

hey all I have an aussie AG 175 1975 model (apparently DT125 gearbox with 175 cylinder- reeds 24mm mikuni etc I just want to see how different hte porting is between cylinders ( or if it is different at all) if anyone has any port pics can they please throw them up cheers ed

First the bike runs great with no known problems. I was out in the desert doin some pd hunting. It was about 90* and I was doin a lot of first gear running. Frequent stops to glass the area then more low gear running on prairie trails. I stopped to turn around and the bike shut off. I tried to start her but no luck. Checked to make sure I was getting fuel to the carb. No problem. This bike usually starts on the first kick. Does the xt350 get hot and just shut down?? I waited about 20 minutes and she fired right up and got me home with no problem. Again is it possible she just got hot from the low gear running in the heat with little air over the fins and just shut…

Dt125

Hello Chaps So I decided to try and figure out what model my DT is... but I'm not winning. Its registered as a 1980 and was originally imported from South Africa. It's mono shock and has round swingarms (not box). Chasis code starts with 4L9-XXX. Apparently the 4L9 code is not listed anywhere on the internet (thanks google). Any ideas about where to look next? I just want to confirm if it is an E, F, G etc. and the actual year of production. Cheers!

Hello chaps. Just wondering if anyone knows if late model disc brakes from a DT175 (2001 onwards in NZ, Aus, SA) will fit on older models? Specifically a 1980 version. Will I need to transplant the entire wheel as well? Will the forks fit? Thanks!

Been watching a 490 on eBay unregistered. £2904. Anybody ever owned one and what did u think? Regards Simon

Hey guys just baught myself a little project. It looked like a classic dt50 but when i checked out the chassis number it came up as a 1977 ty50m. The strange thing is the chassis has a mount for a monoshock and not rear twin shocks. could anyone shed some light on weather they made a single shock version at any point? Thanks in advance guys

Hi everyone, I'm new to the forum and just need a bit of info if anyone can help. I am looking to swap my 09 yz250 in good condition for a 2010 wr450f my question is the Wr450f has 8000 kms on it and has had a top end rebuild at 6000 kms, is that high kilometres for a 2010 and how long do these engines and gearboxes last. thanks in advance

Hello. Welcome i have a WR125 R 2013 recently got it. Anyone got advice. Sent from my iPhone using Tapatalk

Well here we go again you say ! I hope there's a fix for this cos it's doing my head in ! ive done some trawling of posts on here and discovered a problem I didn't know I had, mines a 1980 model,2k4 engine, air filter on the right as you sit, and I believe it should have the 2H500 carb on it, mine has the 3U500 on (160 main ) but, I believe because the air filter I have is more restrictive it'll run rich! It didn't have a filter fitted so I assumed it needed one ( I'm guessing it was run without!) ps. Not used it yet. So, I don't want to source the correct carb cos ( I hope ) this one will maybe go quicker as the other is only a 130 main ! What do you say ? I kn…

Hello I am an 18 year and just bought my first bike about 8 months ago. I own a 1986 XT350 and I am recently having carburetor issues. One of my gaskets are leaking slightly and I want to rebuild it with new gaskets and pieces from a carb kit. Does anyone know if a carb kit exists for the 1986 YDIS carb and if so where can I find it?

Hi,I've had a dt 125 re for about 6 weeks totally original only 9k,problem is only does 50 mph on the flat.i think previous owner just used for commuting never been booted,will it go faster with deep system on,also had a look for this loose wire by the speedo can't find it what colour is it.pls help.

Hi everyone. hope I'm posting this in the right place. Ive built a DTR 125 and completed the mechanical side but struggling to do the electrics. I want it for off road use and need to understand the components I need so it runs and I am unsure what to do with the YPS. Could anyone help please? kind regards Aaron

evening all, just after a little info on the footpegs on a dt125r, i know it may seem a bit anal and over the top but i have found some footpeg rubbers(not the pillion ones) for sale on a website but they are quite expensive so was wondering if all dt125 front footpegs are the same size as the advert states they will fit a DT125re and Dt125dx 04-07 ?, for the record my dt is a 52 plate 125r and the footpeg measures 80mm long and 30mm wide and has a 6mm fixing hole to secure the rubber, thanks

Not sure how we are working this Sent from my SM-J110H using Tapatalk

first time posting new to this just looking for some help with a problem I have with my dtx125 06 plate. basically I bought a dt 125 x but converted it to the off road version the bike has only 4,000 miles spent it's life in a shed! the bike has a full dep system and been fully derestricted and a piper cross air filter, now the problem I am having is when the bike is first started you can not touch the throttle for a good ten minutes of ticking over otherwise it's seems to flood and cut its self off, when the bike is warm it will run fine... on road take the bike off road and pin the throttle open over bumpy surface the bike loses power and does the same what it doe…

Hey, I have got a LED number plate light with my tail tidy, however this LED has got bullet connectors, my bike has got the following kind of connectors. I want to redo the LED light connector as to avoid messing with the stock bike electronics, how would I find out the exact connector which is used for the number plate light, and also the indicators as they are different sizes.

I have a Yamaha dt 125 and can't seem to fined plastics for it at all! Has any one done a YZ plastic conversion? Or somthing along the lines? Thanks

Hi All.. Yes it's a barn find sort of.. I put the bike in there 18 years ago and just found it again. lol Anyway here goes.. Due to being a Suzuki guy and not knowing a great deal about Yams I thought I'd ask you guys for help.. When my son was 9 years old I sold the little quad he's been riding since he was 4 and got him a 1976 YZ80 for him to try 2 wheels.. Well the bike was not running and it turned out to be lack of spark.. Just to get him rolling I changed the old 6volt system to a 12volt total lost system using a gel battery so the bike would run until the battery was dead ( handy for Dads standing around waiting for the kid to get bored and stop ri…

Hello would you be able to tell me the year and model of this dt125 engine I have please the numbers are xE117E007585x thanks in advance I need to know the year as I want to buy a kick mechanism to fit on it.and where I would get one as looking on Ebay and can't find any lol.