Naked

Alright so Im looking to buy an exhaust for my FJ. I found one on ebay for a 1991-1992 FJ1200. Will this fit my bike or no? It is a full exhaust, header midpipe and can. Thanks for the help.

I have owned a 89 FZR 1000 new in 1989, and was sorry i sold it. If anyone has infromation on where I can obtaing one or anyone selling one? It must be mostly stock and with the factory Red/White/Blue body. Must have low miles. Must be in the United States.

Hi guys. I got a fj1200 last month, stood for 2years. Well, got the bike, fitted rings, spark plugs and cleaned the carbs. When trying to sync the carbs, it doesnt idle. Mixture screws is 2 turns out, float correct, jets(pilot and main) newly fitted. Bike runs well if I close the intake of the 4th cylinder carb. Gas going to all the carbs, Struggles to start as well. while i am keeping the bike running with the accelerator and sprying some engine start on carb no 4, it runs well for a few seconds. Took the carb apart, and now if I crank the engine, gas spits out of the air jet. WTF! any anwsers?

I have a 1990 FZR600, are any parts interchangeable with a 1994 FZR600??? Thanks Steve

Just bought a '90 TZR 125 for £220 for a project...... to respray etc........someone has just randomly sprayed it all fully black, such a bodge , anyway it runs clutch works get gears etc.........i will upload pics asap, but i need some advice on what i should do such as colours.....tuning....places to get stuff............also need to know how the power valve works........and also will a tzr 50 front nose fit onto my bike (not one of the new 50's slightly older......they look the same size)

Im just curious since i dont know much about bikes but im about to purchase one Im looking at the history of a bike, engine number is 3HG002169 and states its done over 200000km from 1993-2010 after that its has a different number QE80000223 which the speedo only reads under 10000km from what i can see is that the speedo has been reset to new engine. do these engine numbers mean anything as to capacity size or the engine has been replaced with different a model? thanks

hey guys, i am 23 years old, and im going to get my self a 1991 fzr1000 genesis this week. this is gonna be my 1st bike. i wanted to know from past/present experiences, what were your thoughts on this bike ?? id like it if someone could explain a bit more about the EXUP system, from what ive heard. it is similar to the rotary engine's auxiliary 5th and 6th port. i really like the look on older bikes ... just like my car a own a 1988 Mazda RX7 Turbo2. and insurances arent too bad on that motorcycle. ive had a 900$/2 ways+theft+fire+vandalism quote. heres all i was really able to know from that bike thru internet : Model Yamaha FZR 1000 1991 Motorcycle S…

I had this delivered earlier, needs the original engine rebuilt, it has a DT engine but that hasn't got the right electrical connections so doesn't run ='[ I'll be posting up any progress I make on sunday as I work tuesday, friday and saturday and am at college on the other 3 week days.

Hi guys and girls- it's been a while... So I was cruising from Warwick to Southampton yesterday, and i was coming down the A34 just by Newbury when I felt something pushing on the inside of my right knee- it felt like a strong wind almost. So I glanced down, and as I moved my leg to get a good look the side panel made a dramatic bid for freedom- leaping acrobatically from my bike before crashing to the tarmac some way behind me... And here I am, one side panel down, and wondering "where the hell am I going to get a right hand side panel for a 1991 XJ600?" (before anyone asks- it's not a diversion!) Any ideas guys? Muchas gracias

hello peeps just aquired this bike runs fine revs fine but it doesent seem to charge i did have a few dodgy connection problems from the ignition switch but all good now the bike had been stood for a few 8 years and being a novice i dont know where to go from here any help would be good thanks mark

Allen bolt/ PIN is stripped and Im having a terrible time locating this part. All part searches show a pin that does not have threading. The local dealer also just refers to the part in the Yamaha online micro fish where its shows just a pin and clip. I looked for a used caliper online and also see this, its listed as a 89-93 but has pins Anyone familiar with this type of pin and what bikes have them? Are their different types of pins that Yamaha uses? Please anyone with a 1992 FZR help

A few questions. Looking at a bike that a local Junkyard has for sale. It appears to have been laid down somewhat hard. The front right fairing is cracked and has small pieces missing here and there. Right side rearview mirror is busted off of the mounting arm. Secondary seat is missing. (The elevated seat cushion above the one the rider would sit on. The windscreen is cloudy (just looks like from age) and there is a Red wire that is sticking out from under the gas tank overhang on the right side (looks like it might have gone to the battery, it's bare at the end that is sticking out.) The hand grips are very worn. It has 78k on the odometer. It does have a cl…

So, I took my Seca 2 out for the 1st ride of the year after a long winter. It turns out that my battery is so dead it'll kill my bike if I don't my my rpm over 1500. I'm now in the market of a new battery and the book calls for YTX9-BS. However, the pervious owner put a YTZ12S MF in it. And now I'm thinking about maybe getting a YTZ14S. I am wondering if there is anything against this move. Thanks! Vincent

Hey everybody, just joined. I've got a 92 Seca II that I'm having some problems with. I bought it in May of this year with 7600 miles on it and I rode it about 4000 miles with no problems. Then, one night the lights got dim and it started to die at low RPM's. I kept it revved up and made it home and found the battery dead. I took it to Advance and got it tested, thinking it had dropped a cell or shorted, but it checked good. They charged it for me, checked it again and it was good. With no load, the battery had 12.9 volts and with the bike off, but the ignition on (headlights and ignition energized) it showed 12.6 volts. When I started it, it dropped to about 12.4…

I want to buy an FZR and was prepared to spend 2000 if needed but I'd have to sell my 81 yamaha cafe racer. This was a sad idea but I was prepared to do so. I just found a bike with a clean title that needs some work. That's fine because I am motorcycle savvy and did all the work on the 81 yamaha and others myself. The work: He claims that the shift forks need to be replaced and his motorcycle mechanic buddy told him that. When I went and checked it out, he told me that he has trouble getting past third. I don't remember if he said second doesn't work or not (I know that's a problem for FZRs) but I think it was just getting past third. So I'm wondering if I'm …

Just converted the front brakes to R1 and wow.....I can stop now! Love this bike. New rear Ohlins on the way, can't wait. Any ideas how to snag a tank bra for this bike? Yamaha part number is ABB-3LKTA-NK-CV Have done all the obvious searches. Any help would be great. Secaman at www.prototype900turbo.com

Hello all. I've just bought a 1993 SR125 for my gf to learn on, unfortunatly I when I was looking at it I didn't notice the bend in the front wheel (doh!), not really a problem as I didn't pay too much for it, 'cept it needs to be fixed! My question is this: Does anyone know if the 1993 SR125 came with drum front brake or disc front brake as standard? My one is disc, but I wandered if it had been 'upgraded'.... Also, can anyone see why a front wheel of a later model wouldn't fit? Cheers...

Hi again guys.Having a problem starting the bike.New battery,new plugs but it doesn't fire up.I know its obvious thing after all bike was standing for 2 years,but where should i start?fuel pipes,carbs?Thanks

Hi all,recently bought a yamaha bike,can't figure out what model it is,from the look its srx400 http://i48.tinypic.com/2ahegdv.jpg also can't find vin number where it can be? Thanks to all

Hey all while the manual for my new bike is in the mail, can anyone point me in the direction of float height and spark gap specs for the 93 Virago 750? Thanks