Jump to content

NE0

YOC Member
  • Posts

    722
  • Joined

  • Last visited

  • Days Won

    47

NE0 last won the day on August 3

NE0 had the most liked content!

1 Follower

Previous Fields

  • Current Bike(s)
    Yamaha DT175MX 1978/9. Honda CB400/4 1975

Profile Information

  • Gender
    Male
  • Location
    The Real World

Recent Profile Visitors

11,067 profile views

NE0's Achievements

  1. interesting video here, especially about suspension and preload. might be worth a look. https://www.youtube.com/watch?v=IzXE32thS1g
  2. NE0

    79 xs250

    Did you get it off? Was it completely different to the above? or was my post helpful?
  3. Interesting Digger, I don't know the correct length, but I do know it's probably best not to mix and match different springs. ..........Having said that, had I been doing the clutch back in the 70's/80's I wouldn't have cared about the length or even mix and matching them!!, as long as they weren't broken! and I would have ridden the bike regardless......and I suspect everything would have been fine. Today, I might be a bit more cautious like yourself and try and get the right lengths. although as long as they are all the same, will 1.7mm (the difference between the smallest and largest) make a big difference? I don't sound much help!!.....I'll shut up!
  4. NE0

    79 xs250

    Okay, here's how it works, how a single bolt can remove the rotor. Its different to the DT magneto which has a full length tapered shaft. The XS 250 has a part threaded section within the rotor body. N.B. the normal short bolt with its washer, holds it all in place.
  5. NE0

    79 xs250

    So basically it seems you take out this retaining bolt and replace it with a longer bolt which pops off the Rotor.
  6. NE0

    79 xs250

    I'm not giving up!!....been on Google... looked at the XS400 forum which states it's for the XS250 and XS400 bikes... various searches there suggest the puller is just a bolt The rotor puller Yamaha part number is 90890-01080. It's an M16x1.5 bolt. member Drewpy (is he the same?) says don't use a '3 jaw" puller as you'll f*** up the rotor. another member describes the procedure... Remove the retention bolt that you still have in the photo from the center of the rotor, screw the bigger bolt into the rotor while holding the rotor stationary (manual recommends a special wrench), and rotate the rotor puller/bolt into the rotor. It'll pop off. Cmsnl sell one..https://www.cmsnl.com/products/pullerrotor_9089001080/ hope thats of some help?
  7. NE0

    79 xs250

    looks like we might be getting somewhere....this puller on ebay, specifies for a XS250, although maybe that's several tools in the kit? Hope that's of some help mate. and here's an XS250 Rotor on ebay, ? which suggests a deep internal thread?
  8. NE0

    79 xs250

    In a different post the original poster has stated he can't use this method of puller as the rotor does not have an internal thread. So I did a bit of googling, and came up with this, now i know its not for the XS250 but i wonder if the principle is likely to be the same as this tool is for a Rotor without the internal thread....just a thought. Not quite sure how it works though as this screws onto the shaft but its not threaded on the outside either , unlike my DT one first suggested.
  9. He may well be right Dutch. I had something similar years ago on my 400/4, that has twin coils under the tank directly above the engine. One of them was playing up especially in hot weather. Heat from the engine and warm air from the environment was too much for it and it would often play up in the summer months. A replacement solved the problem. mind you it did take a long time to trace the cause!! Not expensive.. https://www.squaremotorcycleparts.co.uk/products/ignition-coil-yamaha-fj1200-fj-1200-1988-1994 worth doing for that price, and yours will be 32 years old already if original!!
  10. That's good to know Dutch, glad you got it resolved. Plus many thanks for getting back with an update, far too many posts remain 'open' with never an update. For the effort you'll find your name on the leaderboard with a thanks from me, and being the Olympics you might even get a gold medal post! its early days, but you've got a silver medal now...another 'thanks' from someone else will knock me off the Gold!!
  11. NE0

    79 xs250

    I guess he's referring to the magneto stator / rotor? if it is, then the internal thread, highlighted in red takes a magneto puller, the shaft is tapered with a woodruff key to hold the rotor in place. one of these... you put a spanner on the flats to screw it in to the rotor and a socket on the end and screw it in, which then pulls it off the taper. the indent in the shaft end takes the pointed end of the device.
  12. Unfortunatley I can’t teach you how to read a circuit diagram in a forum, its far easier to teach this from a video or in person. Equally unfortunatley you can’t just guess where wires go either, it may well be a rectifier wire, but you need to identify the location of the rectifier first and look for the same wire there, presumably disconnected! To be 100 per cent sure you need some form of meter /Ohm meter to confirm the wire is indeed the same wire at both ends. Regretfully waiting for a V75 owner to chip in with a bit of advice is in my opinion will be a long wait, the forum is relatively quiet these days with few members posting let alone replying, there’s a few regulars like Snakebite and Drewpy and myself but If there were any V75 owners they haven’t replied to any of your previous posts either!! I think your best bet is going to be asking over on the facebook site , at least you’re going to be conversing with someone who actually has one! They should be able to help. Obviously we don’t want to see you go, but if you can let us know how you got on it would be of some help to others with a similar problem.
  13. I see, if you have two red wires, generally the thicker one will be to the battery as it carries more current. Does that help? (unless of course they are both the same thickness.) can you take a photo and post it here?
×
×
  • Create New...