Kelan walker Posted September 23, 2021 Share Posted September 23, 2021 hi everyone this is my first post on the forum as i've looked through many relevant posts but none seem to have my exact problem and was hoping if the much smarter people of this forum could help me. the bike was running fine when i first bought it 2 weeks ago but it has since stopped starting or if it does the front cylinder wont fire and only will start to if i rev the bike, the bike also displays a 3 second engine light which i've seen is related to the voltage regulator, but after replacing it the bike didn't start any better (although the lights on the bike looked much brighter). the battery also gets very hot even after i cleaned the contacts up and has sparked a few times when first pressing the start button then would cut out after the battery arced. if anyone on here has any suggestions it would be much appreciated as i would like to repair this bike entirely myself if possible because id prefer to spend the money on good gear thanks, kelan Link to comment Share on other sites More sharing options...
blackhat250 Posted September 23, 2021 Share Posted September 23, 2021 Sounds like that new reg/rect. is not wired correct, is it same colours in connectors. Link to comment Share on other sites More sharing options...
Kelan walker Posted September 23, 2021 Author Share Posted September 23, 2021 18 minutes ago, blackhat250 said: Sounds like that new reg/rect. is not wired correct, is it same colours in connectors. the old and new one work the same but the engine turns over quicker on the new one Link to comment Share on other sites More sharing options...
Moderator Snakebite68 Posted September 23, 2021 Moderator Share Posted September 23, 2021 1 hour ago, Kelan walker said: ... the battery also gets very hot even after i cleaned the contacts up and has sparked a few times when first pressing the start button then would cut out after the battery arced. ... What's it arcing 'to'? Link to comment Share on other sites More sharing options...
Kelan walker Posted September 24, 2021 Author Share Posted September 24, 2021 22 hours ago, Snakebite68 said: What's it arcing 'to'? the red terminal connector was arcing to the terminal itself =, after sanding it and getting bolts that hold it tighter its no longer arcs the battery also dies fairly quickly Link to comment Share on other sites More sharing options...
Moderator Snakebite68 Posted September 25, 2021 Moderator Share Posted September 25, 2021 First job appears to be a new battery. Don't forget to grease the contacts to reduce corrosion too... Link to comment Share on other sites More sharing options...
Kelan walker Posted September 26, 2021 Author Share Posted September 26, 2021 On 9/25/2021 at 1:44 AM, Snakebite68 said: First job appears to be a new battery. Don't forget to grease the contacts to reduce corrosion too... i was thinking the same thing with the battery. there was also the green goo around a connector that plugs into the starter relay so ill probably have to clean it out but everything is either pointing to a bad connection or dead cell in the battery which i hope 1 Link to comment Share on other sites More sharing options...
neversaydie Posted September 27, 2021 Share Posted September 27, 2021 Your electrical connections and earthing points need to be clean and dry. Charge the battery up fully, le tit stand and see if the voltage drops. Fully charged should be around 13 volts, if it drops quickly after charging its goosed. Try using this fault finding process:https://www.dropbox.com/s/b1x1ojthv4h7925/Troubleshooting 3P PMG %26 RR.pdf?dl=0 Link to comment Share on other sites More sharing options...
Kelan walker Posted November 11, 2021 Author Share Posted November 11, 2021 Sorry for the late post I had trouble signing in since last time I checked the battery which while keys in off position was 10.5v so practically threw that out and bought a new one, bike started no issue after putting it in and would start first crank but has now run into the same issue yet again. From my own look online it could be a fuel issue (either water getting in or clogged floats/jet screw) but I can smell fuel if I flood the cylinders and it makes compression and spark and spins over fine I'm at a wit's end but will try draining the tank and carb completely and if it runs I'll be sure to write in on here and check the intake/filter for leaks as I know the fuel tank cap is good Link to comment Share on other sites More sharing options...
Recommended Posts