Wiffy Posted October 10, 2014 Share Posted October 10, 2014 Is it possible to clean up my exhaust I know I can get the dents blown out I don't really want to paint it as I like the plain metal look there's surface rust and general marks on it was just wondering can I get it looking newish Link to comment Share on other sites More sharing options...
Moderator Airhead Posted October 10, 2014 Moderator Share Posted October 10, 2014 Ahh wiffy paint it fella 1 Link to comment Share on other sites More sharing options...
Wiffy Posted October 10, 2014 Author Share Posted October 10, 2014 Yeah but I like the natural finish airhead I will paint it if I can't clean it up I've not bought it yet I'm waiting for the bloke to tell me the postage cost the pro circuit pipe is supposed to be better than a fmf I read some where sounds nice as well lol airhead, mind the local bobbies won't say that ha ha they didn't like my subaru Link to comment Share on other sites More sharing options...
Wiffy Posted October 10, 2014 Author Share Posted October 10, 2014 I got to do as much searching for bits as I can as I'm back in work next week and won't have as much time on my hands to spend money without the other half finding out ha ha Link to comment Share on other sites More sharing options...
Moderator Airhead Posted October 11, 2014 Moderator Share Posted October 11, 2014 Bits will be hard to find unfortunately...not a big seller here was it! Link to comment Share on other sites More sharing options...
Wiffy Posted October 11, 2014 Author Share Posted October 11, 2014 Well I just bought the pro circuit expansion chamber I found it needs abit of blowing out in a non sexual way as there's a couple of dents on it nothing to bad a bit of surface rust but it was cheap the postage was the same works out under a £100 so a bargin as you can't get these systems anymore just need a 304 study Tail pipe know jetting kit and a filter and maybe some boysen reeds just to make it all run sweet going to have a look for a exhaust blowing kit off ebay ready for when my pipe comes happy days Link to comment Share on other sites More sharing options...
Wiffy Posted October 11, 2014 Author Share Posted October 11, 2014 And yes airhead parts are hard to find been looking out of the uk on sites like webike Japan found my exhaust on eBay in America Link to comment Share on other sites More sharing options...
Moderator Airhead Posted October 11, 2014 Moderator Share Posted October 11, 2014 i'm curious abaout the exhaust blowing kit, I dont need one but if you could post a link i'd like to see it wiffy Link to comment Share on other sites More sharing options...
Wiffy Posted October 11, 2014 Author Share Posted October 11, 2014 Yeah I seen these on eBay only twenty odd quid seen how they work someone with abit of now how could probably knock one up basically clamp on to both ends of exhaust making it air tight it's got a air valve on one end and you fill it till it was about 60 psi and the go over the dents starting from out side of dent with a blow torch circular movements watch it on YouTube for yrself Link to comment Share on other sites More sharing options...
dt502001 Posted October 12, 2014 Share Posted October 12, 2014 Yep I made my own from rubber stoppers for wine the kind you put the air lock in while fermenting were 3 bucks each ,put a bolt ,washers and nut in one stuff it in the pipe and tighten the nut up this expands the rubber for a soild fit,the other one I put a metal valve stem in from a truck same deal install in pipe and tighten the nut then I just put some wire through the spring clamps and ove the rubber plugs they work well takin many a dent out with them. Link to comment Share on other sites More sharing options...
Wiffy Posted October 13, 2014 Author Share Posted October 13, 2014 Hi dt502001 just out of curiosity do yr wheels fit on a wr 200 or are they different Link to comment Share on other sites More sharing options...
dt502001 Posted October 14, 2014 Share Posted October 14, 2014 Don't know check the speedo drive part # if it's the same then yep,axel and bearing's would have to fit in all. Link to comment Share on other sites More sharing options...
Wiffy Posted October 22, 2014 Author Share Posted October 22, 2014 Still waiting for my expansion chamber from the usa my blowing kit has come can't wait to try it out ha want a shorty 304 pro circuit tailpipe to go with it now think I'm going to get a yz125/250 one as they don't do one for mine and they look very close on fitting around 90/95 models might have to give it a little tweak should sound sweet Link to comment Share on other sites More sharing options...
Wiffy Posted October 26, 2014 Author Share Posted October 26, 2014 Found out were my exhaust is customs and they want £25 for the pleasure of delivering my second hand exhaust at least dick Turpin wore a mask when he robbed people . Link to comment Share on other sites More sharing options...
Moderator Airhead Posted October 26, 2014 Moderator Share Posted October 26, 2014 Found out were my exhaust is customs and they want £25 for the pleasure of delivering my second hand exhaust at least dick Turpin wore a mask when he robbed people . yep and the post office will want even more...wait and see !!! Link to comment Share on other sites More sharing options...
Recommended Posts