stat3631 Posted June 22, 2013 Share Posted June 22, 2013 So I have a 1981 DT175 and am having a bit of problems running was looking for some help. I was trying to ride it recently and it would start and get into 1st go a few feet and stall. I did some searching and have: adjusted the petcock for optimal fuel flow adjusted carb float for more gas checked pilot jet and airways put new clamps on carb and filter blocked small hole on case to oil injector I also have two rubber seals on each side of my carb not sure if they are supposed to be there Now it wont idle with choke off and stalls when shifted into gear. I am running pre-mix. From what I have read it could be: stuck clutch plates air leak preventing vacuum carb float level not enough gas Any help is appreciated Link to comment Share on other sites More sharing options...
blackhat250 Posted June 22, 2013 Share Posted June 22, 2013 Yeh plates wil be stuck, put front wheel against wall, ,and with lever pulled in select gear,, if that dont work ,, strip needed, them air joints on carb look iffy, and stock air filtre would be better, to solve the running issues , Link to comment Share on other sites More sharing options...
busyeddie Posted June 23, 2013 Share Posted June 23, 2013 That filter wont help at all, you'll have more luck with a pair of frilly knickers in there. As for stuck plates, old or contaminated oil could be cause. Link to comment Share on other sites More sharing options...
Kkrumb Posted June 24, 2013 Share Posted June 24, 2013 I had similar problems when I took my DT175 out of the shed after 10 years. The clutch was pretty well stuck. I gave it a good push in neutral, jumped on the bike and then put it into first gear while rolling. Unlocked itself in a few goes. Link to comment Share on other sites More sharing options...
Moderator Airhead Posted June 24, 2013 Moderator Share Posted June 24, 2013 That filter wont help at all, you'll have more luck with a pair of frilly knickers in there. As for stuck plates, old or contaminated oil could be cause. That's 'Panties' to you stat Link to comment Share on other sites More sharing options...
flyday58 Posted June 24, 2013 Share Posted June 24, 2013 That's 'Panties' to you stat Yup, over here, knickers is a basketball team. No, wait...like I know anything about sports! I'd also like to see what that petcock optimization looks like, I guess my '78 don't have that. Link to comment Share on other sites More sharing options...
stat3631 Posted June 24, 2013 Author Share Posted June 24, 2013 Well I have a pair I could throw on there. Do the frills help air flow better? The stock is a foam filter right? I will check on ebay. Thanks for the info Link to comment Share on other sites More sharing options...
stat3631 Posted June 24, 2013 Author Share Posted June 24, 2013 Yup, over here, knickers is a basketball team. No, wait...like I know anything about sports! I'd also like to see what that petcock optimization looks like, I guess my '78 don't have that. Yeah it's not the original petcock, I done got me a petcock from the future. You should get you one. Link to comment Share on other sites More sharing options...
blackhat250 Posted June 24, 2013 Share Posted June 24, 2013 Thats not the clutch side , thats the ignition rotor, Link to comment Share on other sites More sharing options...
stat3631 Posted June 24, 2013 Author Share Posted June 24, 2013 Sorry bout that bit of a noob I am clutch pulled in should the plate seperate more with clutch pulled in? Link to comment Share on other sites More sharing options...
blackhat250 Posted June 24, 2013 Share Posted June 24, 2013 Yip , when lever is pulled in they should be loose. do you have a socket set, start by slacken them 5 bolts, if it turns ,slip a 2p in between them cogs, , and place every plate in order they came out, , clean the steel plates with sand paper, or the like as you install them in order, theyre will be rusted marks on them Link to comment Share on other sites More sharing options...
stat3631 Posted June 25, 2013 Author Share Posted June 25, 2013 I took the clutch plates out and they are not rusted together. There is oil between each of them. The oil seem to make them stick but they aren't rusty. Could the clutch not be releasing the plates? Is there any adjustments? Thanks Link to comment Share on other sites More sharing options...
Moderator Airhead Posted June 25, 2013 Moderator Share Posted June 25, 2013 when you put it back together make sure you put that protrusion on each plain plate so that they are equally spaced through 360 degrees or you'll have vibration For adjustment...Leave the cable slack and with your hand push the operating lever on the engine forward until you meet resistance, at this point the pointer on the end of the lever should align with the raised pip on the engine casing...I use the adjusting screw and locknut in the centre of the pressure plate to achieve this. After you've done that...then adjust the cable adjuster to give just a little free play Link to comment Share on other sites More sharing options...
stat3631 Posted July 4, 2013 Author Share Posted July 4, 2013 So I tried adjusting the clutch cable to no avail. But when I removed the plates again, I found that one of the plates is broken one one side. Could that be causing the lurch then stall problem? Also are the rubber rings between supposed to be twisted? Link to comment Share on other sites More sharing options...
blackhat250 Posted July 4, 2013 Share Posted July 4, 2013 No stat " there supposed to be straight, , the lurch you are on about could be rivets on clutch basket excess play. Clearance " check the leanth of both pushrods, and is there a ball in there ? Link to comment Share on other sites More sharing options...
Moderator Airhead Posted July 4, 2013 Moderator Share Posted July 4, 2013 Its no use with a broken plate you'll need a replacement for that Link to comment Share on other sites More sharing options...
Recommended Posts