Migthy Mule Posted September 19, 2012 Share Posted September 19, 2012 Hello all, well its all back together and im taking it for its mot on saturday but I have one last issue and its that the front wheel is not in line with the forks, I have a 24mm gap between the rim and rhand fork, and 32mm gap on the other side??? I dont get it. the spindle is in a fixed position, I tried pushing the one fork leg higher through the yokes but of course this didnt work because the spring just took it up any suggestions ? Link to comment Share on other sites More sharing options...
Moderator Airhead Posted September 19, 2012 Moderator Share Posted September 19, 2012 The RH fork just clamps around a split sleeve on the axle, you should tighten the two clamp nuts up after the spindle nut is tightened and not before...did you do this Sam? Link to comment Share on other sites More sharing options...
Migthy Mule Posted September 19, 2012 Author Share Posted September 19, 2012 Hi, no after because the fork leg (RH) was touching the hub, so I had to pry it away and then tighten it, perhaps I have a spacer missing Link to comment Share on other sites More sharing options...
Moderator Airhead Posted September 19, 2012 Moderator Share Posted September 19, 2012 Assuming the fork legs are not bent Perhaps the forks are twisted in the yokes Remove the front mudguard (for vision) Slacken the RH axel clamp nuts Slacken but leave nipped the four bottom yoke clamp bolts Slacken the three top yoke clamp bolts Enlist a friend to hold the wheel between their legs Twist the handlebar until the wheel appears perpendicular to the handlebar Hopefully this has moved out the RH leg a little? Torque everything back up to spec Forks Upper yoke pinch bolts 18 Steering bolt 43 Lower yoke pinch bolts 14.5 Torque settings in lbf/ft Link to comment Share on other sites More sharing options...
Migthy Mule Posted September 19, 2012 Author Share Posted September 19, 2012 The RH fork just clamps around a split sleeve on the axle, you should tighten the two clamp nuts up after the spindle nut is tightened and not before...did you do this Sam? sorry, just been out to look and yes clamp done up after spindle nut I had considered the twisting in the yokes but ive just tried it and it hasnt made any difference I have no idea if it was always like this, seems likely the forks are bent. ill see if I can turn the forks in the clamps tomorrow Link to comment Share on other sites More sharing options...
Migthy Mule Posted September 20, 2012 Author Share Posted September 20, 2012 Bent Spindle !!!!!!!!!!!!!!!!!!!!!! Link to comment Share on other sites More sharing options...
Migthy Mule Posted September 20, 2012 Author Share Posted September 20, 2012 Anyone know if I need a year specific spindle? will a 125cc spindle fit ? Link to comment Share on other sites More sharing options...
Migthy Mule Posted September 20, 2012 Author Share Posted September 20, 2012 no worries, one on the way Link to comment Share on other sites More sharing options...
Migthy Mule Posted October 14, 2012 Author Share Posted October 14, 2012 the new spindle arrived but was too short, I returned it and got one for a newer model / slightly longer and with a bigger thread that matched the one I removed but this hasnt helped - this got me thinking - could the problem be that I have the wrong front wheel, can anyone enlighten me as to whether the early model dts (round section swing arm) had a narrower hub arrangement, Thanks Link to comment Share on other sites More sharing options...
Moderator Airhead Posted October 14, 2012 Moderator Share Posted October 14, 2012 all the wheels and forks are the same unless you have an imported leading axle style fork Link to comment Share on other sites More sharing options...
Migthy Mule Posted October 14, 2012 Author Share Posted October 14, 2012 http://www.ebay.co.uk/itm/YAMAHA-DT125-SR185-XT-GENUINE-NOS-FRONT-WHEEL-SPINDLE-/261101620379?pt=UK_Motorcycle_Parts&hash=item3ccade8c9b this is listed for 1979 to 1981 and is the same as the first one I ordered, note the reduced size thread the one I removed and have since replaced looked like this : http://www.ebay.co.uk/itm/YAMAHA-DT125-DT175-MX125-TY175-YZ125-AT2-CT2-NOS-GENUINE-FRONT-WHEEL-SPINDLE-/261093973978?ru=http://www.ebay.co.uk/sch/i.html?_sacat=0&_from=R40&_nkw=261093973978&_rdc=1&nma=true&si=VbN9PAO%2Bd6U%2FxrKZk1eyWoQJyUc%3D&orig_cvip=true&rt=nc&_trksid=p2047675.l2557 could it be a wheel from a 250 ? Link to comment Share on other sites More sharing options...
Moderator Cynic Posted October 14, 2012 Moderator Share Posted October 14, 2012 Post a picture of the wheel/fork assy.... Link to comment Share on other sites More sharing options...
Migthy Mule Posted October 14, 2012 Author Share Posted October 14, 2012 all the wheels and forks are the same unless you have an imported leading axle style fork Im having some trouble with photo bucket but im fairly sure its not the leading axle style ( thats where the forks run down behind the spindle i guess) im away monday night but ill get some photos on on Tuesday, thanks Link to comment Share on other sites More sharing options...
Moderator Airhead Posted October 14, 2012 Moderator Share Posted October 14, 2012 thats it then, its not the european version and both the brake plate and axle will be different Link to comment Share on other sites More sharing options...
Migthy Mule Posted October 14, 2012 Author Share Posted October 14, 2012 Just been studying the pictures in your gallery and it looks the same as yours Link to comment Share on other sites More sharing options...
Moderator Airhead Posted October 14, 2012 Moderator Share Posted October 14, 2012 sorry I mis-read what you said! Link to comment Share on other sites More sharing options...
flyday58 Posted October 15, 2012 Share Posted October 15, 2012 Once you have it all together again, try rotating the upper shafts of your fork tubes with the pinch bolts still loose. If that causes the lower tubes to move in or out on the spindle shaft... Cos I just discovered the shiny, unpitted original forks I went to the trouble of rebuilding on my CS5 are both bent. Link to comment Share on other sites More sharing options...
Recommended Posts