fraz24 Posted September 23, 2009 Share Posted September 23, 2009 Been given a set of oxford hot grips(new) and having read the fitting instructions the recommend fitting straight to the battery, I'm not sure about this, can they be fitted via the ignition? Thanks Link to comment Share on other sites More sharing options...
Pvt_Joker Posted September 23, 2009 Share Posted September 23, 2009 Been given a set of oxford hot grips(new) and having read the fitting instructions the recommend fitting straight to the battery, I'm not sure about this, can they be fitted via the ignition? Thanks Id recommend following the instructions Link to comment Share on other sites More sharing options...
Moderator Cynic Posted September 23, 2009 Moderator Share Posted September 23, 2009 Been given a set of oxford hot grips(new) and having read the fitting instructions the recommend fitting straight to the battery, I'm not sure about this, can they be fitted via the ignition? Thanks I'd go with using a relay myself which cuts them off when the ig is off. Link to comment Share on other sites More sharing options...
Moderator Airhead Posted September 23, 2009 Moderator Share Posted September 23, 2009 Newer versions of oxford hotgrips are supposed to shut off if they are inadvertantly left switched on, I think this is when the battery voltage dies down somewhat, Quote their website "To prevent the battery of the vehicle from being discharged when the engine of the vehicle is turned off, the Heat Controller has sophisticated software that will automatically switch off all power to the HOTGRIPS before the battery voltage becomes very low. However, the voltage maybe too low to restart the vehicle as it is designed to ensure that the battery is not permanently damaged and can still be recharged. This voltage is set at between 10.5 - 11.0 Volts." So at worst you will need to bump start your bike, which on a 125 shouldnt be too hard. A relay would be the best way if you can be bothered though.Hotgrips Linky Link to comment Share on other sites More sharing options...
fraz24 Posted September 24, 2009 Author Share Posted September 24, 2009 Newer versions of oxford hotgrips are supposed to shut off if they are inadvertantly left switched on, I think this is when the battery voltage dies down somewhat, Quote their website "To prevent the battery of the vehicle from being discharged when the engine of the vehicle is turned off, the Heat Controller has sophisticated software that will automatically switch off all power to the HOTGRIPS before the battery voltage becomes very low. However, the voltage maybe too low to restart the vehicle as it is designed to ensure that the battery is not permanently damaged and can still be recharged. This voltage is set at between 10.5 - 11.0 Volts." So at worst you will need to bump start your bike, which on a 125 shouldnt be too hard. A relay would be the best way if you can be bothered though.Hotgrips Linky Thanks for the advice! Link to comment Share on other sites More sharing options...
RogerH Posted December 8, 2009 Share Posted December 8, 2009 Thanks for the advice! I've fitted these so they turn off with the ignition. Trouble is they'd turn off when riding if I stopped at a junction or sometimes just at slow speed in traffic. I replaced the battery as it was over 5 years' old but the same thing. I sent the control unit back to the seller who sent me another but I still have the same problem. Anyone got any ideas? as so far I'm really unhappy with these... Link to comment Share on other sites More sharing options...
Moderator Cynic Posted December 8, 2009 Moderator Share Posted December 8, 2009 I've fitted these so they turn off with the ignition. Trouble is they'd turn off when riding if I stopped at a junction or sometimes just at slow speed in traffic. I replaced the battery as it was over 5 years' old but the same thing. I sent the control unit back to the seller who sent me another but I still have the same problem. Anyone got any ideas? as so far I'm really unhappy with these... It will be the control box switching the grips off because the bike cannot supply enough power at low rpm. Its up to you but i'd sooner the grips cut out than the motor. It would also mean the undignified experience of bumping the bike if the grips didn't cut in and out, don't look so cool outside the chippy, especially as with all the elecronic whatsits and doodahs on modern bikes there is no gaurantee it will bump with a low battery. Link to comment Share on other sites More sharing options...
Recommended Posts