Jump to content

pilninggas

Free
  • Posts

    1,312
  • Joined

  • Last visited

  • Days Won

    29

Posts posted by pilninggas

  1. 44 minutes ago, drewpy said:

    are you coming to Darley D?

     

    i will if i can. as you know the first week of the school year tends to be busy. one of my work hats is health&safety manager, so it might not be easy to get away on that friday.

    im hopeful ill have a clear picture by the weds so i can phone the pub if it's on, and make sure i am booked in.

  2. 2 hours ago, drewpy said:

    do you need a centre stand on with the 3 wheels or are the Nikkens not self standing?

    its not self standing, although i do think it could be easily balanced at traffic lights, once im used to it.

  3. i thought it was bank holiday weekend, but just reread and it's the first weekend of Sept. I'll hold back as work maybe mad that week.

    Perhaps ill come up on the Sat, ill only be able to call it when i see what week 1 is like.

  4. 1 hour ago, Cynic said:

    Crikey, makes my 400 mile day round snowdon look a bit lame. Was a great day though, air was crisp for a lot of it, sun came out around 2. Lake bala especially is stunning.

     

    yeah Bala is nice.i get up that way quite a bit.

  5. I just did Scotland. Weather was pretty good, though not hot. Even NW500 was just damp.

    I prebooked every stay, and it turned out to be a good move, as loads of places had no vacancies.

    2600miles in 10 days with enough time to walk Ben Nevis and Three Dodds.

    • Like 1
  6. 80000kms should be fine on an FZR1000 engine.

    as said above I'd avoid doing a rebuild - the costs are eye watering and as some of the parts are out of production by yam, so you will spend time sourcing parts elsewhere. Even if the 'economy is not important' don't end up blowing so much money you could have bought a fitter newer bike instead.

    Many of those era Yams with 5 valves burn oil (valve stem seals leak) so that might need doing but it is a top end job [and the valve clearances too]. My EXUP has 63000kms and although the engine isnt particularly quiet (they sound harsh by most standards), it's good to go.

    I find it's chassis and brakes that need more care on these things at these higher mileages (km-ages) and if the engine is good focus on these.

  7. Stator's usually have 4 wires (in one cable sheathing/loom) coming out of them (3 phases and an earth). I'd find out what this wire goes to. If the other wires on the stator are the same colour (yellow perhaps?) then it may well be the earth.

     

    You need to get sight of a wiring diagram, so you can see what it goes to.

  8. cant you drill the old nipple out? you can buy nipples with 0.5 oversize for this reason. You can also buy bleedable banjos, they replace the existing banjo but have a bleed nipple built in - i have fitted one and as long as you orientate the caliper correctly you can bleed them out. They look like this:

    Yamaha YZF-R 125 16 Banjo Bolt for Front Caliper (Stainless Steel ...

     

    if you must replace the caliper, do you know the bolt spacing? 

    There are a number of yamahas with the same ~(i think) 83mm calipers.

     

     

     

    • Like 2
    • Thanks 1
  9. I had a 535. got it cheap because the carbs were sticky. Remove the diaphram caps and check that the vacuum operated slides are freely moving. Unlike most bikes they are led on their sides and need ptfe spray to keep them free.

    Change the plugs if you havent yet done that, as that improves performance under load.

    If these dont cure it then check air filter and carb jets.

×
×
  • Create New...